The formation of a stable and adherent oxide layer on the Ti-6Al-4V alloy can improve the mechanical and corrosion resistance of this material. This work studied the creep behavior of Ti-6Al-4V alloy after two different thermal oxidation conditions: at 650 °C for 12 h and at 800 °C for 2 h. In the XRD analysis of the oxidized samples, it was possible to observe the formation of rutile (TiO2) and a displacement of the peaks of α and β phases caused by the dissolution of oxygen. In the creep test at 550 °C, the material oxidized at 800 °C for 2 h showed a greater creep life at 125 MPa, the crack took longer to brake probably due to the greater thickness of the layer. At 550°C and 187.5 MPa the material oxidized at 650 °C for 12h has a better creep life, probably due to the layer more adhered.

The copper alloy UNS-C27200 is a binary brass, composed of 38wt%Zn, beeing one of the most used in the industry. The union of Cu-Zn alloys by conventional welding by fusion in thin plates presents several challenges. The Friction Stir Welding (FSW) process performs the union of two, or more materials, through a rotating tool that travels throughout the welding region. One the great advantages of FSW is working below the melting point of the material, which reduces the change in the microstructure and properties of the material, when compared to conventional welding processes. Due to the lack of research on FSW process in lap brass joints with thin thicknesses, the present work aims to expand these studies in order to contribute to future research. Eight conditions were evaluated, varying rotation and welding speed. In the best results by visual inspection, analyzes of microstructure, temperature, microhardness and mechanical strength were performed. The better welding results were obtained with ω=1050 rpm and ν=20 mm/min. There was reduction of approximately 50% between Stir Zone and Base metal. The mechanical strength was affected by the pin hole resulting from the process. The microstructure revealed a homogeneous mixture in the stir zone and no defects were detected.

Ti alloys are widely used in severe corrosion environments where corrosion resistance is required, as biomedical industry. Additive manufacturing produces customized and complexes products. Laser texturing is a process of structuring surfaces using laser pulses, that allows the creation of periodic patterns on the surfaces of materials, to modify them, functionally and/or aesthetically, in a precise and direct way, allowing parameterization, versatility and repeatability. Consequently, bringing together metallic additive manufacturing with laser texturing process could be an alternative to obtain parts with functional hydrophilic surfaces, which improves osteointegration and reduces bacteria adhesion. Thus, the aim of this work is to characterize and evaluate the influence of LASER parameters in as-built additive manufactured potential biomedical components. Ti6Al4V specimens were produced by L-PBF, using Ytterbium LASER with maximum power of 500 W, varying the laser power from 61 W to 244 W. The samples were characterized by SEM, Microhardness, and wettability. After that, some specimens were Laser textured using an Ytterbium optical fiber laser, and then evaluated by SEM, wettability, and 3D roughness. It was possible to observe that the surface of all studied samples was flattened after Laser texturing in comparison with as-built condition, due to the melting of the powder particles.

Abstract Over the years, the demand for high engine efficiency has resulted in the development of new generation superalloys with improved elevated temperature properties, especially creep resistance. This study aimed to evaluate creep and mechanical behavior of Inconel 718 superalloy. Creep tests were performed at temperature range of 650 to 700 °C and stress range of 625 to 814 MPa. Hot tensile and oxidation tests were performed and the characterization techniques used in this study were scanning electron microscopy (SEM) for microstructural and fracture surface analysis, transmission electron microscopy (TEM) for precipitates analysis; grazing X-ray diffraction for analysis of oxide formation and Vickers microhardness. The analyze of stress exponent value (n = 36.48) and activation energy (Qc = 512.97 kJ/mol), suggested that creep mechanism at 650 °C was the climb dislocation mechanism. The Inconel 718 presented ductile fracture at 650 and 700 °C and intergranular fracture to 675 °C.

Metals solidification involves the transformation of the molten metal back into the solid state. Solidification structures impact heavily on the final product's characteristics. The microstructure effects on metallic alloys properties have been highlighted in various studies and particularly the dendrite arm spacing influence upon the mechanical properties such as tensile strength has been reported. In the present investigation, Al-10wt%Si-2wt%Cu and Al-10wt%Si-5wt%Cu alloys were directionally solidified upward under transient heat flow conditions. The experimental results include solidification thermal parameters such as tip growth rate and cooling rate, optical microscopy, volume fraction of the eutectic mixture, primary dendritic arm spacing and ultimate tensile strength. Experimental growth laws of primary dendrite arm spacing as a function of the solidification thermal parameters are proposed. The Hall-Petch mathematical expressions were used to correlate the ultimate tensile strength as a function of the primary dendritic arm spacing. It was found that the alloy with higher copper content had a more refined structure. More refined structures had higher ultimate tensile strength values.

Plasma nitriding of a solution annealed and aged 300 grade maraging steel was studied aiming to increase the creep resistance. The surface microhardness reached 1,140 HV, producing 50 µm layer composed of ε-Fe3N and γ'-Fe4N nitrides at the uppermost sample layer. The inner core remained unaltered presenting typical plate-like martensite microstructure of maraging steels with average microhardness of 604 HV. Surface RMS roughness in the nanometric scale increase from 52 nm to 71 nm. The continuous layer of iron nitrides seems to behave as a barrier for oxidation and for inward oxygen diffusion improving the creep resistance by reducing the steady-state creep rate (εs) in 52-65% when compared with the literature results. Dominant creep mechanism is controlled by dislocations climb. Fracture surfaces of specimens presented ductile failure consisting of equiaxed and bi-modal dimples in the fibrous zone surrounded by 45º shear lip. Nitrided sample presented a reduced ductility, associated to the hard surface layer.

Biomaterials (composites and blends) play a major role in the health of modern society. This paper reports on the preparation and characterization of polyvinylidene fluoride (PVDF) and hydroxyapatite (HAP) composites, analyzing the incorporation of HAP in PVDF and investigating their mechanical properties and cytotoxicity (biocompatibility) for use in bone restoration and filling. The material was prepared in film form by the casting method. PVDF pellets were dissolved in dimethylacetamide (DMA), a HAP/DMA emulsion was prepared. The materials were mixed in proportions of 100/00, 90/10, 80/20, 70/30, 60/40, 50/50, 40/60, 30/70 in weight and left to dry in an oven, resulting in homogeneous, flexible films which were characterized by scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS), X ray diffractometry (XRD), contact angle measurement, and by mechanical and cytotoxicity tests.